+- Forums (https://www.studioscalemodelers.com/forums)
+-- Forum: Index (https://www.studioscalemodelers.com/forums/forum-623.html)
+--- Forum: Studio Scale Replica Builds In Progress (https://www.studioscalemodelers.com/forums/forum-678.html)
+--- Thread: ROTJ MINIATURE Y WING (/thread-2869.html)
ROTJ MINIATURE Y WING - Ralphee - 05-17-2019
Hey all.
I started IDing this model a few weeks ago, making great progress on mapping her out.
Only a few silly parts now remain to be found now, so we made a test print hull, thanks Marvin, to start trying most physical parts on.
It wasn't too far out, but the dims still needed adjusting in many areas based on donor part information.
To start to get a better understanding of the model as a whole, I've started to apply some of the more b grade castings to this hull, a handy ref tool if you will.
One kit for sure used on this model does come after the release of ROTJ, which is interesting in itself. Yet a single gun barrel Y was shot for the Endor Battle.
Its possible this was re-dressed in the case of the Propstore Y wing, but, it's all conjecture until concrete proof is supplied.
In any case, it's been fun to kick it all off, it's quite a cute yet fairly elaborate model as a whole.
Lee
RE: ROTJ MINIATURE Y WING - Ralphee - 05-19-2019
A few more test castings applied. Cant wait for the new revised hull now and play with real parts
Lee
RE: ROTJ MINIATURE Y WING - JAWS - 05-20-2019
Very kool.
RE: ROTJ MINIATURE Y WING - Ralphee - 05-30-2019
Just the domes to pull, a makeshift cockpit and this V1 test is about ready to be shelved.
The new V2 hull should be underway by now, and I'll be starting on a new build, and master pattern.
This does adorn some slightly incorrect M5A1 parts purely as I dont wish to waste anything but off cuts I already have on this one. All other parts are waste resin casts, and just there to test out hull dims, so most of the plant on detail is now also in rubber.
Fun little thing, and I've now learned a lot on what to put right for the final builds, always good to have a physical dry run.
Bests......Lee
RE: ROTJ MINIATURE Y WING - Ralphee - 06-01-2019
A makeshift rough as buggery, Jerry rigged cockpit to give it some size. The actual pattern will be quite different, just the domes to add and this one goes to bed and V2 will begin.
Lee
RE: ROTJ MINIATURE Y WING - Ralphee - 07-27-2019
Finally started the V2 build. This is to be a master pattern for molding. Once the hull is complete, I'll move on to the engine cans, of which I'd like to mold/cast as a one piece tube, and just a membrane to scalpel out to fit.
Lee
RE: ROTJ MINIATURE Y WING - Turrican - 08-02-2019
What was wrong with V1?
Both look spot on.
RE: ROTJ MINIATURE Y WING - Ralphee - 08-02-2019
Just needed some adjustments based on part fitment, few other areas were altered too, small changes that really improved it. The V1 is redundant now but was very handy in having a physical shape to figure a few things out.
Lee
RE: ROTJ MINIATURE Y WING - marvin - 08-02-2019
Just the difference between “good” and “great” 😊
RE: ROTJ MINIATURE Y WING - Ralphee - 08-03-2019
Indeed Marvin. It's all falling into place very well now.
Lee
RE: ROTJ MINIATURE Y WING - Ralphee - 08-04-2019
Upper hull master now finished. Lower hull master isn't far behind now too. Some parts have been modded to allow a flush fit for molding ease, but should make an excellent base to jump off now.
RE: ROTJ MINIATURE Y WING - Ralphee - 08-06-2019
Lower hull generic pattern now done. Few marks in the print to spot fill, but very happy with part fitment which is overall very close indeed. Off to the resin artist with these and I can work on the engine cans, I've missed using solvent, as binding these parts on with CA has been a chore.
RE: ROTJ MINIATURE Y WING - Turrican - 08-06-2019
Super clean, super sharp, wonderful work!
RE: ROTJ MINIATURE Y WING - NS4 - 08-06-2019
Wow - looking fantastic Lee. Lovely work as always!
RE: ROTJ MINIATURE Y WING - Ralphee - 08-06-2019
Thanks so much both. The hull has been a journey between two of us, Marvin kindly loaned his hand to create firstly the original hull, based on my extensive donor research.
From that point, the V1 was then further tweaked to a V2 as I went along placing parts and assessing the fit.
Still a few parts to find but it's been a very fun project, and this hasn't hampered the process of creating the masters, as the small missing parts can be added later easily enough.
Lee
RE: ROTJ MINIATURE Y WING - Ralphee - 03-17-2020
Some progress.
Lee
RE: ROTJ MINIATURE Y WING - Ralphee - 03-21-2020
A quick update as paint has begun to be slung on the build for my resin man.
Using exclusively Archive-X enamels as there is nothing out there that's reliable, plentiful and matches the original ILM period tones.
Still much to do, but it's taking shape now.
Lee
RE: ROTJ MINIATURE Y WING - Ralphee - 03-24-2020
Suddenly there were two.
Lee
RE: ROTJ MINIATURE Y WING - Turrican - 03-25-2020
Great stuff as always Lee.
Paint looks spot on as well.
Also ordered new stuff from Guy some time ago.
Sadly no time currently for building my B-Wing...but time will come...time will come.
RE: ROTJ MINIATURE Y WING - JAWS - 03-26-2020
Woh. Nice stuff.
RE: ROTJ MINIATURE Y WING - Ralphee - 03-31-2020
First one completed. Tons of fun. Will be offering completed models at some point in the future.
Lee
RE: ROTJ MINIATURE Y WING - Ralphee - 04-12-2020
Been messing about with a few castings and thought I'd base a Gold 2 on this 1/48 ROTJ base model. Lots of fun. Swapped a few parts out too just for fun.
Bests ... Lee